Farm Collector

SHOW REPORT

Chappell, Nebraska

Because I am interested in collecting and restoring antique
engines, I was invited to help with the annual Steam and Gas Engine
Show at Bridgeport, Nebraska this fall and it proved to be one of
the most interesting days a house painter (my trade) could ask
for.

It takes a lot of hands to keep those old monsters running and
some fancy footwork to line them up and handle the big crowd that
attends. Little things like sand in your shoes or sanburrs in your
socks are forgotten when one of the big ones makes a successful
swing around the parade ground. And they were all there –
Aultman-Taylor, J.I. Case, Waterloo Boy, Rumely, John Deere, Huber
– to name a few.

The old Aultman-Taylor came to an obstinate halt half-way around
and had to be dragged off by a proud old Case. The 12-ton giant was
a load for the smaller steamer and the smoke billowed and the steam
rolled as it dug into the sand. I had misgivings about the Waterloo
Boy but it made it without a hitch. Last year the governor stuck
and I had to drop into low gear and run by adjusting the speed on
the carburetor

The 1910 two-cylinder Rumely was hard to start because it has
make and break ignition (no spark plugs). The old monster gave the
little G. P. John Deere tractor a tussle just to turn over those
immense iron flywheels, let alone start it; but the big
four-cylinder Huber came around the parade ground with its head in
the air, no smoke and without missing a shot.

We had one ancient hard-tired G. M. G. which we finally got
started by advancing the spark by hand. It has no battery, just a
magneto. I held the spark lever while my assistant engineer drove.
Those old rigs are hard to steer and when we came a-round the
corner, we ended up against a tree. To complicate our
embarrassment, it took quite a while to find reverse and get back
on course.

One of the most interesting added attractions was a steam
calliope pulled by a pair of bay mares. It was run by an electric
motor.

The crowd also liked the 22-inch, hand-fed Case separator
powered by eight head of horses. This year it had a
‘cheater’ on it because it had given the horses such a load
last year. A car transmission was installed next to the separator,
but you could still hear that beveled gear drive pick up speed and
it did my heart good to hear that old familiar sound.

Among the one cylinder gasoline engines was a real work of art
by Don Messing, Route 2, Sidney, Nebraska. Its shinny black
castings and bright red flywheel were mounted on a four-wheel steel
frame. The engine, a twelve horse Seager, was found in a scrap heap
and took many months to restore. The piston was rusted tight and to
loosen it, Messing packed it with dry ice and used a twelve ton
jack to move it a little at a time. Some parts were missing and had
to be handmade. The ignition is a battery and Model-T coil.

The engine was made by Seager Engine Works, Lansing, Michigan
and dated 1908 or 09. The motor appears to be older than that, a
12-horse Olds, 250, Type A-6. The original owner was Raymond Walker
who lived in Iowa. It was brought to Nebraska in 1916 and used on a
corn sheller. It has a horizontal saucer muffler. The block is cast
in sections and has a pot head. The red and black paint is purely a
guess as there was too much rust to find a hint of the original
color.

There were also an old Sears Roebuck, six horsepower upright I.
H. C., John Deere, two Fairbanks-Morse and a Fuller and Johnson
geared to a pump jack.

My latest acquisition is a small Novo, upright, one cylinder
engine which I found and bought at Wallace, Nebraska enroute home
from the steam engine reunion at Bird City, Kansas.

I would like to tell other readers that anyone having trouble
finding good drip oilers that they can get them at the Cornhusker
Machinery Co. in North Platte, Nebraska.

  • Published on Jan 1, 1967
© Copyright 2022. All Rights Reserved - Ogden Publications, Inc.