Farm Collector

The Nichols & Shepard Excello Separator and the Reason For Building It

Salina, Kansas

Straw racks in Red River Special steel separators with 15 bar
cylinders, built prior to 1925, consisted of five shakers. The
first four shakers were carried and driven by the Brady shaker
carriers on the inside of the separator. Those shaker carriers were
carried by four wooden, hangers pivoted at the top. Two wooden
hangers attached to the sides of each of the four shakers of the
rack and pivoted from the top. Those hangers were on the inside of
the separator and moved close to the sides of the separator. When
the carriers moved ahead and back, the arms attached to the sides
of the shakers and pivoted at the top, produced the up and down
movement of the shakers. The last shaker was carried by four
hangers on the outside of the separator and driven by two short
pitmans from the shaker carriers.

Wild oats was plentiful in 1923 on the Minneapolis Territory.
Wild oats straw did not dry cure and become brittle as did domestic
oats, barley and wheat straw. It wound around shafts and collected
where other straw caused no trouble.

The wheat crop on the Salina Block was short in 1923 and Nichols
and Shepard Company inquired about my going north. I never had
worked in the north and told the company I would be pleased to go.
Nichols and Shepard Company instructed me to report to the
Minneapolis Branch and I arrived there ahead of schedule.

I was not there long, until I learned the tough wild oats straw
was causing straw rack trouble in the steel separators by
collecting between the shaker arms and the sides of the separators.
So much straw finally collected, it bulged the sides of the
separator and created so much friction, it was necessary to stop
and remove the straw. The service men seemed unable to do anything
to prevent it.

Nichols & Shepard Company considered re-designing the
separator in such a way, the hangers would have been on the outside
of the separator to overcome that trouble but it would have been
costly to build and the company decided to build a differently
designed separator. Nichols & Shepard Co., before building the
new machine, wrote their salesmen and inquired, which separator
they premerred, a Case or a Wood Bros.

Nichols & Shepard Co., bought a Wood Bros. separator,
shipped it to the factory and built 300 Excellos.

The frame of a Wood Bros, separator was constructed of straight
steel and the deck was straight. The only noticeable difference in
the design of a Wood Bros, and an Excello frame, was in the shape
of the decks. The deck of the Excello, over the beater, sloped
toward the cylinder, with a short abrupt slope toward the wind

The straw rack of a Wood Bros. separator was of four sections
and rotated on crankshafts. The bottom of the grain-pan was
corrugated, the shoe an end shake and the fan an undershot. All
Nichols & Shepard fans were over-shot. The Wood Bros. separator
was without a beater and the straw rack contained nothing upon
which tough straw could collect or wrap.

An Excello was nearly a duplicate of a Wood Bros, separator. The
only noticeable difference was the front end. The front end was
Nichols and Shepard. The cylinder, concaves, Man Behind the Gun,
beater and tailings elevator were Nichols & Shepard. Wood
Bros., because of the similarity of the machines, stopped Nichols
and Shepard from building Excellos.

Wood Bros. were highly honorable men and liberal in settlement
with Nichols & Shepard Company. That Company paid Wood Bros,
for the making of those Excellos. R. B. Lyman, deceased, manager
for Nichols & Shepard Company at the Kansas City Branch in 1924
said, ‘Nichols & Shepard Company paid Wood Bros, by
contracting work done in Wood Bros., shops.’ Wood Bros, shops
were more modern than Nichols & Shepard shops.

Nichols & Shepard Co., sold those Excellos and the reports
on them were excellent but when Nichols and Shepard had to pay for
building them that Company built no more Excellos. No company ever
received better advertising than Wood Bros., when Nichols &
Shepard Co., built those Excellos.

The next year, 1925, Nichols and Shepard Company re-designed the
frame of the steel separator. The sills were of one piece and
sloped from the front to the rear. Shafts of the cylinder, beater,
fan, wind stacker, belt tighteners and belt guide were equipped
with Hyatt roller bearings. Nearly all pulleys were fiber. The
straw rack was the regular Nichols & Shepard rack. The hangers
remained inside the separator but moved closer to the sides than in
separators made prior to 1925.

  • Published on Jan 1, 1955
© Copyright 2022. All Rights Reserved - Ogden Publications, Inc.